Load a land survey drawing or registry certificate (PDF), or a SIMA file, onto the map
Plans: all plans (including Free). Reading a PDF requires signing in (free). Loading a SIMA file does not. No AI credits are used.
What you can do
- Read a land survey drawing (PDF): the coordinates in the coordinate table are read, the area computed from them is cross-checked against the area stated on the drawing, and the parcel is overlaid on the map.
- Read a land registry certificate: the location, lot number, land category and area are read from the title section of a land registry certificate (PDF) and shown. You can also see the difference from the area you measured on the map. Owner names, addresses and similar data are not read.
- Load a SIMA file: show a parcel on the map from your own SIMA (coordinate data) file.
Once shown, the parcel can be used as it is for checking the area and side lengths, exporting to DXF, SIMA, JWW or CSV, printing, and splitting by area.
Where to start
The measurement panel (press "Measure" 📏 on the map) has "📄 Load a PDF or SIMA file". You can use it before drawing anything. It opens with:
| Item | Details |
|---|---|
| Zone | Normally leave it on "Auto (estimated from the map position)" |
| Survey drawing PDF | Choose a PDF up to 4 MB |
| Registry certificate PDF | Choose a PDF of a land registry certificate |
| SIMA file | Choose a SIMA file up to 5 MB and 2,000 points |
Read a land survey drawing PDF
- Move the map near the parcel (it helps when the zone is judged automatically).
- Press "Survey drawing PDF" and choose the PDF. If you are not signed in, a notice and a "Sign in (free)" button appear.
- "Reading…" is shown. It usually takes 10 to 30 seconds. Please wait.
- On success the parcel is shown on the map with the number of points, the area and the zone.
For safety, the reader does the following:
- It checks that the area computed from the coordinates matches the area stated on the drawing. A parcel that does not match is not shown.
- It reads the drawing in two different ways and shows the parcel only when all coordinates agree. If they do not agree, nothing is shown.
- It returns numbers only and does not follow instructions written in the drawing.
Note: If a stamp or handwriting overlaps a digit, an error may remain. Check important values against the original coordinate table. If one drawing carries coordinate tables for several parcels, only one parcel (normally the first) is read. Check the lot number and coordinates shown against the drawing.
Read a land registry certificate
- Press "Registry certificate PDF" and choose the PDF of a land registry certificate. If you are not signed in, a notice and a "Sign in (free)" button appear.
- "Reading…" appears. It usually takes 10 to 30 seconds.
- When it succeeds, the title section (location, lot number, land category, area) is shown. If you have drawn a parcel on the map, the difference from the area you measured (in m² and %) is shown too.
- Only the title section (description of the land) is read. The owner's name and address, mortgages and other entries in the rights sections are excluded from what is read and are not returned to your screen.
- As with survey drawings, the same document is read twice in a different order, and the result is shown only when the lot number, land category, area and so on agree. If they do not, "Not shown: the readings were not stable" appears, and the read is not counted.
- Building registry certificates cannot be read ("Could not read the land title section" appears, and the read is not counted). For a certificate of a unit in a condominium building, the land held with the unit (site rights) may be readable.
- The values shown are reference values, not the registry record itself. Check the Legal Affairs Bureau for the latest. The area measured on the map is not treated the same as the registered area.
- We tried the sample certificates (scanned images) published by the Ministry of Justice. For the land sample, the location, lot number, land category and area were read correctly. For the building sample, the read was refused because it is not land. For the condominium-unit sample, the land held with the unit was read in some attempts and not in others (a read that fails is not counted). Results depend on the actual condition of your document (stamps, folds, faint text).
Load a SIMA file
- Press "SIMA file" and choose the file (.sim or similar).
- The zone is estimated from the current map position, and "judged to be Zone N" is shown. If it is wrong, choose another zone in the box and press "Read again with this zone".
- With 3 or more points, the parcel is shown on the map.
Guide to scan and copy quality
- Use documents that are 300 dpi or more, without tilt, with clearly legible text.
- Fax copies and low-resolution black-and-white copies make digits easier to misread. In tests with strongly degraded synthetic scans, registry certificates were mostly not shown at fax-like quality (we check that two readings agree, so as not to show a wrong value). For survey drawings, there were cases at fax-like quality where the coordinates were shown off by 2 to 8 mm.
- Handwriting, folds, show-through, faint text and overlapping stamps may stop a result from being shown. When a result is shown, check the lot number, area and coordinates against the original.
When it does not work
The screen shows the likely cause and the next step. The main ones are:
| Message | Cause and what to do |
|---|---|
| Could not read the coordinates reliably | Check that the page shows the coordinate table (point, X, Y), and that it is 300 dpi or more without tilt. Try a PDF with only the table page |
| Not shown: the coordinates do not match the stated area | The difference between the computed area and the stated area is shown. A digit, decimal point or sign may have been misread. Try a clearer PDF |
| Not shown: the readings were not stable | The two readings did not agree. A stamp or handwriting may overlap the digits |
| The zone could not be read / the coordinates fall outside Japan | Choose the zone in the box and read again without choosing the file again |
| Shown, but away from where you are looking | The zone may be wrong. You can choose another in the box |
| Could not read the land title section (registry certificate) | It may be a building certificate, or a PDF that does not show the title section. Choose a land registry certificate that shows location, lot number, land category and area. The read is not counted |
| No coordinates found (SIMA) | Check that it is a SIMA file, that the order is X (north), Y (east) in metres, and that it is not garbled |
Monthly limits and failed reads
Reading a PDF (survey drawing or registry certificate) has a monthly limit (separate from AI credits; both kinds of reading use the same count).
| Plan | Per month |
|---|---|
| Free | 30 |
| Starter | 150 |
| Pro | 300 |
| Business | 1,000 |
| Enterprise | Unlimited |
- A read that does not succeed (unreadable, the cross-check does not match, or a temporary failure) is not counted. Up to 10 such reads a month per person are given back. Beyond that they are counted, and the screen says so.
- The limit resets on the 1st of each month (Japan time).
- Loading SIMA files is not limited.
How PDFs are handled
- The PDF you upload is read by AI in Japan and is not stored on MAPRISE servers. Only the numbers read are returned to your screen.
- A registry certificate PDF may contain third parties' personal information, such as the owner's name and address. This is excluded from what is read, but upload the document only if you are authorised to handle it.
- For details, see the Privacy Policy.
Values read are reference only. They are not survey results and have no legal evidentiary value.